If you have plugged in a USB device (usually a mass storage device) into a computer and it doesnt work, here are some basic troubleshooting steps to resolve the problem. Why Modern Android Devices Don’t Support USB Mass Storage. USB mass storage — also known as “USB mass storage device class,” USB MSC, or UMS — was the way. How to Fix Slow USB 3. Problems in Windows 8. For various PC problems, we recommend to use this tool. This tool will repair common computer errors, protect you from file loss, malware, hardware failure and optimize your PC for maximum performance. It’s MTP not USB mass storage, like on every other honeycomb tablet, so annoying. Quickly fix PC issues and prevent others from happening with this software: Download Reimage. Plus (1. 00% safe download). Click “Start Scan” to find Windows issues that could be causing PC problems. Click “Repair All” to fix all issues (requires upgrade). Quite a lot of users have been experiencing problems with their USB 3. Windows 8. 1. Most of them are reporting that the port is very slow or not responding at all. Read below to find more about this. Here we go again, more Windows 8. USB 3. 0 functionality. I’ve been following this Windows 8. Mostly, what Windows 8. USB 3. 0 or other problems, such as a connected mouse, external hard drive or other device not being recognized. One user is reporting a problem with a Dell laptop: I have Dell Inspiron N5. I upgraded to windows 8. USB port on the right side has stopped working. I cannot find the chipset drivers for 8. Any good suggestion ? While another Lenovo user is complaining about this: I have a T4. CTO, running Windows 8. Prior to upgrade from Windows 8. The USB 3 ports worked correctly, in particular running an external 1gb hard drive. After update to 8. USB 3 ports still work, but only for about 3. The power light is still lit on the hard drive, but it no longer shows in windows explorer. In device manager, I went to Universal Serial Bus Controllers - > USB Root Hub - > Properties- > (under General it says “This device is working properly)- > Power Management- > Unchecked the box for “Allow the computer to turn off this device to save power”. Unfortunately this does not seem to stop problem. Any ideas? Those affected by USB 3. OEM’s – Buffalo, dat. Ashur, Fantom Drive, Fujitsu, Hitachi, ADATA Nobility, Kingston Data. Traveler, La. Cie 2. TB USB Drive, Raid. Sonic, Sans Digital, Vantect, Fantec, Digitus, Mediasonic, Samsung 1. T, Apricorn, i. Storage, Disk. Genie, Verbatim, Western Digital. Here are a few solutions that you could try to make it work. The first basic solution you could try is by going into device manager, find the USB root hubs, and turn off the save power option. If not, then follow these steps: To view the idle period that some USB devices use to save power. Type “power options” in Search Charm. Change Plan Settings of the currently selected power plan. Click Change advanced power settings. Expand Hard disk and then Turn off hard disk after. The Setting value indicates the system disk idle period. In this image the idle period is set to 2. For this system, if no file transfers occur within 2. For most USB storage devices and USB host controllers, the power- saving mechanism works without issues. However, a pre- existing problem in the USB drive or USB host controller might cause these problems after the specified idle period expires. The device periodically disconnects and might reconnect leading to poor user experience. If so, get the latest firmware from the system or device manufacturer. A firmware update might resolve the issue. Otherwise, determine whether the problem occurs during the system disk idle time period (shown in Power Options). If it does, disable suspend on idle for this device as per the instructions given in the next section. Note, you can set the value to “Never” in the Power Options just an experiment to see if that fixes the issue, but the right long term solution is to set the registry setting as described below. This registry setting does not affect the other USB storage devices and results in conserving power. How to disable suspend on idle. Get the hardware ID of the USB storage device. For various PC problems, we recommend to use this tool. This tool will repair most computer errors, protect you from file loss, malware, hardware failure and optimize your PC for maximum performance. Quickly fix PC issues and prevent others from happening with this software: Download Reimage. Plus (1. 00% safe download and endorsed by us). Click “Start Scan” to find Windows issues that could be causing PC problems. Click “Repair All” to fix all issues. Make sure the device is plugged in. Search for “device manager” in the Search charm, and open Device Manager. In Device Manager, expand the Disk Drives and locate the device: Select the View > Devices by connection from the menu: Right- click the USB Mass Storage Device node under which the device appears, and select Properties. On the Details tab, select Hardware Ids from the drop- down list. Make a note of the 4 digits occurring after “VID. In this example, VID is 0. PID is 0. 00. 1. Change the device setting in the registry. Run Registry Editor (regedit. Search charm. Right- click the regedit icon, and select Run as administrator. In Registry Editor, navigate to HKEY. The name must be VID and PID strings obtained previously. Leading 0’s are significant. For the device in this example the new key name is “0. Right- click the new key and create a DWORD entry named Device. Hack. Flags. Set the value to 4. Disconnect and reconnect the device. The solution has been posted by the Microsoft Windows USB Core Team Blog (didn’t even know there existed such a team). Anyway, let us know if this managed to solve your USB 3. Windows 8. 1. Tags: windows 8.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
October 2017
Categories |